SFPTvariableAirVolume

Variable Air-Volume Controller (VAV).  nciSetPnts is not defined in the profile due to its type inheriting from the Principal NV of the profile. No mandatory NVs are of SNVT_temp_setpt, and therefore it cannot inherit the correct type.  
 

Network Variables

Configuration Properties

nviSetPoint
nviSpaceTemp
nvoSpaceTemp
nvoUnitStatus

nviApplicMode
nviBoxFlow
nviCO2
nviDuctInTemp
nviEmergCmd
nviEnergyHoldOff
nviFanSpeedCmd
nviHeaterOverid
nviManOverride
nviOccCmd
nviSetpointOffset
nvoBoxFlow
nvoEffectSetPt
nvoEnergyHoldOff
nvoFlowControlPt
nvoTerminalLoad

nciMaxFlow
nciMinFlow
nciSetPnts
nciSndHrtBt

nciDuctArea
nciLocation
nciMinFlowHeat
nciMinFlowStand
nciMinOutTm
nciNomFlow
nciRcvHrtBt
nciRcvHrtBtN01
nciRcvHrtBtN05
nciRcvHrtBtN07
nciRcvHrtBtN10
nciRcvHrtBtN11
nciRcvHrtBtN13
nciRcvHrtBtN15
nciSndHrtBtNV03
nciSndHrtBtNV04
nciSndHrtBtNV16
nciSndHrtBtNV18
nciSndHrtBtNV19
nciSndHrtBtNV20
nciVAVgain

 

Details:

Resource Set: Standard 00:00:00:00:00:00:00:00-0
Index: 50
Obsolete: no
Key: 8010
Inheriting: no


Mandatory Network Variables

nviSpaceTempSpace Temperature Input.:   This input network variable is used to connect an external space temperature sensor to the node. 
Member Number: 1
Base type:
SNVT_temp_p
Direction: input
Service: any
Minimum: 10,00
Maximum: 50,00
nviSetPointTemperature Setpoint Input.:   This input network variable is used to allow the temperature setpoint for the occupied and standby mode to be changed via network. 
Member Number: 2
Base type:
SNVT_temp_p
Direction: input
Service: any
Minimum: 10,00
Maximum: 35,00
nvoSpaceTempSpace Temperature Output.:   This output network variable is used to send the value of the controlled space temperature to other nodes. 
Member Number: 3
Base type:
SNVT_temp_p
Direction: output
Service: unacknowledged
Minimum: -10,00
Maximum: 50,00
nvoUnitStatusUnit Status Output.:    
Member Number: 4
Base type:
SNVT_hvac_status
Direction: output
Service: unacknowledged
Minimum: HVAC_HEAT,0,000,0,000,0,000,0,000,0,000,0
Maximum: HVAC_NUL,100,000,100,000,100,000,100,000,100,000,255


Optional Network Variables

nviApplicModeApplication Mode Input.:   This network variable input is used to coordinate the VAV object with the air handler control or any other supervisory controller or intelligent human interface device.  
Member Number: 5
Base type:
SNVT_hvac_mode
Direction: input
Service: any
nviManOverrideVAV Manual Override Input.:   This input network variable is used for commanding the controller into a manual mode. 
Member Number: 6
Base type:
SNVT_hvac_overid
Direction: input
Service: any
Maximum: HVO_NUL,100,000,65535
nviSetpointOffsetSetpoint Offset Input.:   This input network variable is used to shift the temperature setpoint via the network by adding nviSetpointOffset to the current setpoint. 
Member Number: 7
Base type:
SNVT_temp_p
Direction: input
Service: any
Minimum: -10,00
Maximum: 10,00
nviOccCmdOccupancy Input.:   This input network variable is used to command the VAV objectinto different occupancy modes. 
Member Number: 8
Base type:
SNVT_occupancy
Direction: input
Service: any
nviEmergCmdEmergency Command Input.:   This input network variable is used to command the VAV object into different emergency modes. 
Member Number: 9
Base type:
SNVT_hvac_emerg
Direction: input
Service: any
nviBoxFlowBox Flow Input.:   This variable represents the input to a VAV controller object from a flow sensor on the network. 
Member Number: 10
Base type:
SNVT_flow
Direction: input
Service: any
Minimum: 0
nviEnergyHoldOffEnergy Hold-Off Input.:   This input is from a device such as a window contact sensor. 
Member Number: 11
Base type:
SNVT_switch
Direction: input
Service: any
nviFanSpeedCmdFan-Speed Command Input.:   This input network variable is used to connect an external fan speed switch to the node or to allow any supervisory device to override the fan speed controlled by the node's control algorithm.  
Member Number: 12
Base type:
SNVT_switch
Direction: input
Service: any
nviCO2CO2 Sensor Input.:   This input network variable measures the CO2 levels in PPM. 
Member Number: 13
Base type:
SNVT_ppm
Direction: input
Service: any
Maximum: 5000
nviHeaterOveridHeater Override Input.:   This input disables to be turned on by the VAV controller. 
Member Number: 14
Base type:
SNVT_switch
Direction: input
Service: any
nviDuctInTempDuct-Inlet Temperature Input.:   If the duct inlet air temperature sensor is a LONMARK device, the VAV controller object obtains its value through this network variable. 
Member Number: 15
Base type:
SNVT_temp_p
Direction: input
Service: any
Minimum: -10,00
Maximum: 50,00
nvoEffectSetPtEffective Setpoint Output.:   The output network variable is used to inform the effective setpoint temperature when the setpoint is changed by local means. 
Member Number: 16
Base type:
SNVT_temp_p
Direction: output
Service: unacknowledged
Minimum: 10,00
Maximum: 35,00
nvoFlowControlPtEffective-Flow Control-Point Output.:   The output network variable is used to inform the effective control point used by the flow control loop. 
Member Number: 17
Base type:
SNVT_flow
Direction: output
Service: unacknowledged
nvoBoxFlowBox Flow Output.:   The output network variable is used to provide the flow in the box. 
Member Number: 18
Base type:
SNVT_flow
Direction: output
Service: unacknowledged
nvoTerminalLoadTerminal Load Output.:   The output network variable is used to provide the demand for supply energy. 
Member Number: 19
Base type:
SNVT_lev_percent
Direction: output
Service: any
nvoEnergyHoldOffEnergy Hold-Off Output.:   This output is used to convey to other devices the state of an EnergyHoldOff device that is hardwired to the controller. 
Member Number: 20
Base type:
SNVT_switch
Direction: output
Service: unacknowledged
Minimum: 0,0 0
Maximum: 100,0 1


Mandatory Configuration Properties

nciSndHrtBtSend heartbeat.:   The maximum period of time between consecutive transmissions of the current value. 
Member Number: 1
Base type:
SCPTmaxSendTime
Applies to SFPTvariableAirVolume
Array: not permitted
Default: 0,0
nciMinFlowMinimum flow.:   The minimum flow. 
Member Number: 6
Base type:
SCPTminFlow
Applies to SFPTvariableAirVolume
Array: not permitted
Default: 0
nciMaxFlowMaximum flow.:   The maximum flow. 
Member Number: 7
Base type:
SCPTmaxFlow
Applies to SFPTvariableAirVolume
Array: not permitted
Maximum: 65535
Default: 65535
nciSetPntsOccupancy temperature setpoints.:   The occupancy temperature setpoints for heat and cool mode. 
Member Number: 24
Base type:
SCPTsetPnts
Applies to SFPTvariableAirVolume
Array: not permitted
Minimum: -10,00,-10,00,-10,00,-10,00,-10,00,-10,00
Maximum: 35,00,35,00,35,00,35,00,35,00,35,00
Default: 23,00,25,00,28,00,21,00,19,00,16,00


Optional Configuration Properties

nciRcvHrtBtReceive heartbeat.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 2
Base type:
SCPTmaxRcvTime
Applies to SFPTvariableAirVolume
Array: not permitted
Default: 0,0
nciMinOutTmMinimum send time.:   The minimum period of time between consecutive transmissions of the current value. 
Member Number: 3
Base type:
SCPTminSendTime
Applies to SFPTvariableAirVolume
Array: not permitted
Default: 0,0
nciLocationLocation:   Provides descriptive physical location information related to the object. 
Member Number: 4
Base type:
SCPTlocation
Applies to SFPTvariableAirVolume
Array: not permitted
Default: 00*31
nciDuctAreaDuct area or size.:   The duct area used to calculate the air flow, relevant only for VAV actuators / controllers. 
Member Number: 5
Base type:
SCPTductArea
Applies to SFPTvariableAirVolume
Array: not permitted
Maximum: 13,1068
Default: 0,0000
nciMinFlowHeatMinimum heating airflow.:   The minimum airflow setpoint of a VAV terminal while heating. 
Member Number: 8
Base type:
SCPTminFlowHeat
Applies to SFPTvariableAirVolume
Array: not permitted
Default: 0
nciMinFlowStandMinimum flow for standby.:   The minimum flow through the VAV box in standby mode. 
Member Number: 9
Base type:
SCPTminFlowStby
Applies to SFPTvariableAirVolume
Array: not permitted
Default: 0
nciNomFlowNominal air flow.:   Value used in calculating the air flow in an airflow control actuator. 
Member Number: 10
Base type:
SCPTnomAirFlow
Applies to SFPTvariableAirVolume
Array: not permitted
Minimum: 0
Maximum: 4750
Default: 0
nciVAVgainVAV gain.:   The gain of the VAV controller object. 
Member Number: 11
Base type:
SCPTgainVAV
Applies to SFPTvariableAirVolume
Array: not permitted
Default: 1,0000
nciSndHrtBtNV18Maximum send time.:   The maximum period of time between consecutive transmissions of the current value. 
Member Number: 13
Base type:
SCPTmaxSendTime
Applies to nvoBoxFlow
Array: not permitted
Default: 0,0
nciSndHrtBtNV19Maximum send time.:   The maximum period of time between consecutive transmissions of the current value. 
Member Number: 14
Base type:
SCPTmaxSendTime
Applies to nvoTerminalLoad
Array: not permitted
Default: 0,0
nciSndHrtBtNV16Maximum send time.:   The maximum period of time between consecutive transmissions of the current value. 
Member Number: 15
Base type:
SCPTmaxSendTime
Applies to nvoEffectSetPt
Array: not permitted
Default: 0,0
nciSndHrtBtNV20Maximum send time.:   The maximum period of time between consecutive transmissions of the current value. 
Member Number: 16
Base type:
SCPTmaxSendTime
Applies to nvoEnergyHoldOff
Array: not permitted
Default: 0,0
nciRcvHrtBtN01Maximum receive time.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 17
Base type:
SCPTmaxRcvTime
Applies to nviSpaceTemp
Array: not permitted
Default: 0,0
nciRcvHrtBtN07Maximum receive time.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 18
Base type:
SCPTmaxRcvTime
Applies to nviSetpointOffset
Array: not permitted
Default: 0,0
nciRcvHrtBtN05Maximum receive time.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 19
Base type:
SCPTmaxRcvTime
Applies to nviApplicMode
Array: not permitted
Default: 0,0
nciRcvHrtBtN10Maximum receive time.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 20
Base type:
SCPTmaxRcvTime
Applies to nviBoxFlow
Array: not permitted
Default: 0,0
nciRcvHrtBtN11Maximum receive time.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 21
Base type:
SCPTmaxRcvTime
Applies to nviEnergyHoldOff
Array: not permitted
Default: 0,0
nciRcvHrtBtN13Maximum receive time.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 22
Base type:
SCPTmaxRcvTime
Applies to nviCO2
Array: not permitted
Default: 0,0
nciRcvHrtBtN15Maximum receive time.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 23
Base type:
SCPTmaxRcvTime
Applies to nviDuctInTemp
Array: not permitted
Default: 0,0
nciSndHrtBtNV03Maximum send time.:   The maximum period of time between consecutive transmissions of the current value. 
Member Number: 25
Base type:
SCPTmaxSendTime
Applies to nvoSpaceTemp
Array: not permitted
Default: 0,0
nciSndHrtBtNV04Maximum send time.:   The maximum period of time between consecutive transmissions of the current value. 
Member Number: 26
Base type:
SCPTmaxSendTime
Applies to nvoUnitStatus
Array: not permitted
Default: 0,0