SFPTdamperActuator

Damper Actuator..  Three sub types of HVAC actuators can be handled by this object: general purpose, fire & smoke, and airflow control. 
 

Network Variables

Configuration Properties

nviActuatState
nviRelStpt
nvoActualValue

nviEmergOvrd
nviManOvrd
nvoAbsAirFlow
nvoAbsAngle
nvoActuatStateFb
nvoDuctTemp
nvoEmergOvrdFb
nvoRelStptFb

nciDirection
nciMaxSendTime
nciMinSendTime
nciRcvTime

nciActuatType
nciDriveTime
nciDuctSize
nciLocation
nciMaxSetpoint
nciMinSetpoint
nciNomAirFlow
nciNomAngle
nciOemType
nciSendOnDltAngl
nciSendOnDltFlow
nciSendOnDltTemp
nciTempSensConst
nciVavSensConst

 

Details:

Resource Set: Standard 00:00:00:00:00:00:00:00-0
Index: 37
Obsolete: no
Key: 8110
Inheriting: no


Mandatory Network Variables

nviRelStptActuator setpoint input.:   Controls the relative actuator setpoint. 
Member Number: 1
Base type:
SNVT_lev_percent
Direction: input
Service: any
Minimum: 0,000
Maximum: 100,000
nviActuatStateActuator state input.:   Used where the actuator is connected to a switch that forces the actuator to a predefined set of positions or air volumes. 
Member Number: 2
Base type:
SNVT_switch
Direction: input
Service: any
nvoActualValueActual position output.:   Present position of the actuator. 
Member Number: 3
Base type:
SNVT_lev_percent
Direction: output
Service: unacknowledged
Minimum: 0,000
Maximum: 100,000


Optional Network Variables

nviEmergOvrdEmergency override input.:   Used in fire and smoke applications to open and close an actuator with maximum speed; this input has highest priority. 
Member Number: 4
Base type:
SNVT_hvac_emerg
Direction: input
Service: any
nviManOvrdManual override input.:   Command the actuator into a manual mode (mainly used during balancing) 
Member Number: 5
Base type:
SNVT_hvac_overid
Direction: input
Service: any
nvoActuatStateFbActuator state feedback output.:   Mirrors the actual value of nviActuatState. 
Member Number: 6
Base type:
SNVT_switch
Direction: output
Service: unacknowledged
nvoRelStptFbActuator setpoint feedback output.:   Mirrors the actual value of nviRelStpt. 
Member Number: 7
Base type:
SNVT_lev_percent
Direction: output
Service: unacknowledged
Minimum: 0,000
Maximum: 100,000
nvoAbsAngleDamper angle output.:   Present position of the actuator's shaft or damper blade. 
Member Number: 8
Base type:
SNVT_angle_deg
Direction: output
Service: unacknowledged
nvoAbsAirFlowAir flow output.:   Airflow through the associated VAV box. 
Member Number: 9
Base type:
SNVT_flow
Direction: output
Service: unacknowledged
nvoDuctTempInside duct temperature output.:   Present temperature inside the duct. 
Member Number: 10
Base type:
SNVT_temp_p
Direction: output
Service: any
Minimum: -50,00
Maximum: 150,00
nvoEmergOvrdFbEmergency override feedback output.:   Mirrors the value of nviEmergOvrd. 
Member Number: 11
Base type:
SNVT_hvac_emerg
Direction: output
Service: unacknowledged


Mandatory Configuration Properties

nciMinSendTimeMinimum send time.:   The minimum period of time between consecutive transmissions of the current value. 
Member Number: 1
Base type:
SCPTminSendTime
Applies to SFPTdamperActuator
Array: not permitted
Default: 30,0
nciMaxSendTimeMaximum send time.:   The maximum period of time between consecutive transmissions of the current value. 
Member Number: 2
Base type:
SCPTmaxSendTime
Applies to SFPTdamperActuator
Array: not permitted
Default: 0,0
nciRcvTimeMaximum receive time.:   The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.  
Member Number: 3
Base type:
SCPTmaxRcvTime
Applies to SFPTdamperActuator
Array: not permitted
Default: 0,0
nciDirectionDirection / Safety position.:   The actuator sense of rotation and safety position; bit 0 set => counterclockwise, bit 1 set => damper open. 
Member Number: 4
Base type:
SCPTdirection
Applies to SFPTdamperActuator
Array: not permitted
Default: 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0


Optional Configuration Properties

nciSendOnDltFlowFlow send on delta.:   The minimum change in airflow required to be treated as significant. 
Member Number: 5
Base type:
SCPTminDeltaFlow
Applies to nvoAbsAirFlow
Array: not permitted
Default: 10
nciSendOnDltTempMinimum delta temperature.:   The minimum change in temperature required to be treated as significant. 
Member Number: 6
Base type:
SCPTminDeltaTemp
Applies to nvoDuctTemp
Array: not permitted
Minimum: 0,00
Default: 1,00
nciSendOnDltAnglDamper angle send on delta.:   The minimum change in damper actuator angle required to be treated as significant. 
Member Number: 7
Base type:
SCPTminDeltaAngl
Applies to nvoAbsAngle
Array: not permitted
Minimum: 0,00
Default: 5,00
nciActuatTypeActuator label.:   The identification of the exact actuator type or label. 
Member Number: 8
Base type:
SCPTactuatorType
Applies to SFPTdamperActuator
Flags: manufacturer specific
Array: not permitted
nciOemTypeOEM label.:   The label, programmed by the OEM, to identify the unit name. 
Member Number: 9
Base type:
SCPToemType
Applies to SFPTdamperActuator
Flags: device specific, constant
Array: not permitted
nciLocationLocation:   Provides descriptive physical location information related to the object. 
Member Number: 10
Base type:
SCPTlocation
Applies to SFPTdamperActuator
Array: not permitted
nciDriveTimeDrive time.:   The transition time for a full 100% stroke (change from one extreme to the other) 
Member Number: 11
Base type:
SCPTdriveTime
Applies to SFPTdamperActuator
Array: not permitted
Default: 150,0
nciNomAngleNominal angle.:   The nominal angle for an actuator. 
Member Number: 12
Base type:
SCPTnomAngle
Applies to SFPTdamperActuator
Array: not permitted
Minimum: 0,00
Maximum: 95,00
Default: 90,00
nciNomAirFlowNominal air flow.:   Value used in calculating the air flow in an airflow control actuator. 
Member Number: 13
Base type:
SCPTnomAirFlow
Applies to SFPTdamperActuator
Array: not permitted
nciDuctSizeDuct area or size.:   The duct area used to calculate the air flow, relevant only for VAV actuators / controllers. 
Member Number: 14
Base type:
SCPTductArea
Applies to SFPTdamperActuator
Array: not permitted
nciMaxSetpointMaximum range.:   The maximum limit of the value of the primary output network variable for the object. 
Member Number: 15
Base type:
SCPTmaxRnge
Applies to nvoActualValue
Array: not permitted
Default: 00*2-4E-20
nciMinSetpointMinimum range.:   The minimum limit of the value of the primary output network variable for the object. 
Member Number: 16
Base type:
SCPTminRnge
Applies to nvoActualValue
Array: not permitted
nciVavSensConstVAV sensor constant.:   Calibration constant used to calculate airflow. 
Member Number: 17
Base type:
SCPTsensConstVAV
Applies to SFPTdamperActuator
Array: not permitted
nciTempSensConstTemperature sensor constant.:   Calibration value for a duct temperature sensor. 
Member Number: 18
Base type:
SCPTsensConstTmp
Applies to SFPTdamperActuator
Array: not permitted