Unit-Ventilator Controller.. Used to control an HVAC unit ventilator.
|
| |
Network Variables | Configuration Properties |
nviSpaceTemp
nvoEffectSetpt
nvoSpaceTemp
nvoUnitStatus
nviApplicMode
nviAuxHeatEnable
nviComprEnable
nviEconEnable
nviEmergOverride
nviEnergyHoldOff
nviFanSpeedCmd
nviHeatCool
nviOccManCmd
nviOccSchedule
nviOccSensor
nviOutdoorRH
nviOutdoorTemp
nviSetpoint
nviSetptOffset
nviSetptShift
nviSourceTemp
nviSpaceCO2
nviSpaceRH
nviValveOverride
nvoCoolPrimary
nvoDischAirTemp
nvoEffectOccup
nvoEnergyHoldOff
nvoFanSpeed
nvoHeatCool
nvoHeatPrimary
nvoHeatSecondary
nvoLoadAbsK
nvoOADamper
nvoOutdoorRH
nvoOutdoorTemp
nvoSetpoint
nvoSetptShift
nvoSpaceCO2
nvoSpaceRH
nvoTerminalLoad
| nciSetPoints
nciSndHrtBt
nciBypassTime
nciLocation
nciManualTime
nciMinOutTm
nciNumValve
nciOAMinPos
nciRcvHrtBt
nciRcvHrtBtNV01
nciRcvHrtBtNV03
nciRcvHrtBtNV04
nciRcvHrtBtNV05
nciRcvHrtBtNV07
nciRcvHrtBtNV08
nciRcvHrtBtNV09
nciRcvHrtBtNV11
nciRcvHrtBtNV12
nciRcvHrtBtNV13
nciRcvHrtBtNV14
nciRcvHrtBtNV17
nciRcvHrtBtNV18
nciRcvHrtBtNV19
nciRcvHrtBtNV20
nciRcvHrtBtNV41
nciSndHrtBtNV21
nciSndHrtBtNV22
nciSndHrtBtNV23
nciSndHrtBtNV25
nciSndHrtBtNV27
nciSndHrtBtNV28
nciSndHrtBtNV31
nciSndHrtBtNV32
nciSndHrtBtNV33
nciSndHrtBtNV34
nciSndHrtBtNV35
nciSndHrtBtNV36
nciSndHrtBtNV37
nciSndHrtBtNV38
nciSndHrtBtNV39
nciSndHrtBtNV40
nciSpaceCO2Lim
nciSpaceHRSetpt
|
| |
Details: |
| Resource Set:
| Standard 00:00:00:00:00:00:00:00-0 |
| Index:
| 76 |
| Obsolete:
| no |
| Key:
| 8080 |
|
Inheriting:
| no |
|
Principal Variable
| nviSpaceTemp |
Mandatory Network Variables |
| nviSpaceTemp | Space Temperature Input.: This input network variable is used to connect an external space temperature sensor to the node.
|
| Member Number:
| 1 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nvoSpaceTemp | Effective Space Temperature Output.: This output network variable is used to monitor the effective space temperature that the Chilled Ceiling Controller is using for control.
|
| Member Number:
| 21 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoEffectSetpt | Effective Setpoint Output.: This output network variable is used to monitor the effective temperature setpoint.
|
| Member Number:
| 22 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoUnitStatus | Unit Status Output.: This output network variable is available to report the Unit Ventilator Controller status.
|
| Member Number:
| 23 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
Optional Network Variables |
| nviSetpoint | Temperature Setpoint Input (absolute): This input network variable is used to allow the temperature setpoints for the occupied and standby modes to be changed via the network.
|
| Member Number:
| 2 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviSetptOffset | Setpoint Offset Input.: This input network variable is used to shift the effective occupied and standby temperature setpoints by adding nviSetptOffset to the current setpoints.
|
| Member Number:
| 3 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviSetptShift | Setpoint Shift Input.: This input network variable is used to shift the effective heat/cool setpoints by adding the corresponding value in nviSetptShift to the current setpoints.
|
| Member Number:
| 4 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviOccSchedule | Occupancy Scheduler Input.: This input network variable is used to command the Unit Ventilator Controller into different occupancy modes.
|
| Member Number:
| 5 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviOccManCmd | Occupancy Override Input.: This input network variable is used to command the Unit Ventilator Controller into different occupancy modes.
|
| Member Number:
| 6 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviOccSensor | Occupancy Sensor Input.: This input network variable is used to indicate the presence of occupants in the controlled space.
|
| Member Number:
| 7 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviApplicMode | Application Mode Input.: This network variable input is used to coordinate the Unit Ventilator Controller with any supervisory controller.
|
| Member Number:
| 8 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviHeatCool | Heat/Cool Mode Input.: This network variable input is used to coordinate the Unit Ventilator Controller with any node that may need to control the heat/cool changeover of the unit.
|
| Member Number:
| 9 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviFanSpeedCmd | Fan Speed Command Input.:
This input network variable is used to connect an external fan speed switch to the node or to allow any supervisory device to override the fan speed controlled by the node's control algorithm.
|
| Member Number:
| 10 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviComprEnable | Compressor Enable Input.: This input is used to disable compressor operation. This input is typically sent from a system coordination panel.
|
| Member Number:
| 11 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviAuxHeatEnable | Auxiliary Heat Enable Input.: This input is used to disable auxiliary heat operation. This input is typically sent from a system supervisor panel.
|
| Member Number:
| 12 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviEconEnable | Economizer Enable Input.: This input is used to enable and disable economizer operation.
|
| Member Number:
| 13 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviEnergyHoldOff | Energy Hold Off Input.: This input is used to stop heating and cooling while allowing the unit to protect the space from temperature extremes.
|
| Member Number:
| 14 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviValveOverride | Water Valve Override Input.: This input network variable is used for commanding the controller into a manual mode for overriding water valves controlled by the unit.
|
| Member Number:
| 15 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviEmergOverride | Emergency Override Input.: This input network variable is used to command the device into different emergency modes. It is typically set by a supervisory node.
|
| Member Number:
| 16 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviSourceTemp | Source Temperature Input.: This input network variable is used to indicate the temperature of the air or water being supplied to the unit for heating and/or cooling capacity.
|
| Member Number:
| 17 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviOutdoorTemp | Outdoor Air Temperature Input.: This input network variable represents information from an outdoor air temperature sensor.
|
| Member Number:
| 18 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviSpaceRH | Percentage level.: This input network variable is the measured space humidity in percent. This input is typically sent from a communicating humidity sensor.
|
| Member Number:
| 19 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nviOutdoorRH | Outdoor Air Humidity Input.: This input network variable is the measured outdoor humidity in percent.
|
| Member Number:
| 20 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
| nvoEffectOccup | Effective Occupancy Output.: This output network variable is used to indicate the actual occupancy mode of the unit.
|
| Member Number:
| 24 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoHeatCool | Effective Heat/Cool Output.: This output network variable is used to indicate the actual heat/cool mode of the unit.
|
| Member Number:
| 25 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoSetpoint | Local Setpoint Output.: This output network variable is used to monitor the space temperature setpoint if a setpoint device is locally wired.
|
| Member Number:
| 26 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoSetptShift | Local Setpoint Shift Output.: This output network variable is used to report a locally-determined shift of the effective heat/cool setpoints.
|
| Member Number:
| 27 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoFanSpeed | Fan Speed Output.: This output network variable reflects the actual fan speed of a local multi-speed fan as well as the requested speed of a remote fan.
|
| Member Number:
| 28 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoDischAirTemp | Discharge Air Temperature Output.:
This output network variable is used to monitor the temperature of the air that leaves the Unit Ventilator Controller, if the unit controller provides a hardwired temperature sensor for this purpose.
|
| Member Number:
| 29 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoLoadAbsK | Absolute Power Consumption KW Output.: This output network variable can used to indicate the current power consumption of the unit.
|
| Member Number:
| 30 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoTerminalLoad | Terminal Load Output.: This output indicates the current heat/cool energy demand of the unit.
|
| Member Number:
| 31 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoHeatPrimary | Primary Heat Output.: This output network variable reflects the current level of the primary heat output or can be used to control a remote primary heat source.
|
| Member Number:
| 32 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoHeatSecondary | Secondary Heat Output.: This output network variable reflects the current level of the secondary heat output or can be used to control a remote secondary heat source.
|
| Member Number:
| 33 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoCoolPrimary | Primary Cool Output.: This output network variable reflects the current level of the primary mechanical cooling output or can be used to control a remote mechanical cooling source.
|
| Member Number:
| 34 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoOADamper | Outdoor Air Damper Output.: This output network variable reflects the current position of the outdoor air damper or as a request to a remote outdoor air damper.
|
| Member Number:
| 35 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoSpaceRH | Space Humidity Output.: This output network variable indicates the space humidity in percent, if the Chilled Ceiling Controller Device has a locally wired humidity sensor.
|
| Member Number:
| 36 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoOutdoorRH | Outdoor Air Humidity Output.: This output network variable indicates the outdoor air humidity in percent, if the Unit Ventilator Controller Device has a locally wired humidity sensor.
|
| Member Number:
| 37 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoOutdoorTemp | Outdoor Air Temperature Output.: This output network variable is used to monitor the outdoor air temperature if the unit controller provides a hardwired temperature sensor for this purpose.
|
| Member Number:
| 38 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoSpaceCO2 | Space CO2 Sensor Output.: This output network variable indicates the space CO2 concentration in ppm, if the Unit Ventilator Controller Device has a locally wired CO2 sensor.
|
| Member Number:
| 39 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nvoEnergyHoldOff | Energy Hold Off Output.: This output indicates the state of an Energy Hold Off device that is hardwired to the controller.
|
| Member Number:
| 40 | |
Base type:
| | | Direction:
| output | | Service:
| unacknowledged |
|
| nviSpaceCO2 | Space CO2 Sensor Input.: This input network variable measures the space CO2 levels in PPM.
|
| Member Number:
| 41 | |
Base type:
| | | Direction:
| input | | Service:
| any |
|
Mandatory Configuration Properties |
| nciSetPoints | Occupancy temperature setpoints.: The occupancy temperature setpoints for heat and cool mode.
|
| Member Number:
| 17 | |
Base type:
| | |
Applies to
| SFPTunitVentilatorController | | Array:
| not permitted | | Minimum:
| -10,00,-10,00,-10,00,-10,00,-10,00,-10,00 | | Maximum:
| 35,00,35,00,35,00,35,00,35,00,35,00 | | Default:
| 23,00,25,00,28,00,21,00,19,00,16,00 |
|
| nciSndHrtBt | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
|
Optional Configuration Properties |
| nciSndHrtBtNV25 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 4 | |
Base type:
| | |
Applies to
| nvoHeatCool | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV27 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 5 | |
Base type:
| | |
Applies to
| nvoSetptShift | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV28 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 6 | |
Base type:
| | |
Applies to
| nvoFanSpeed | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV31 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 7 | |
Base type:
| | |
Applies to
| nvoTerminalLoad | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV32 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 8 | |
Base type:
| | |
Applies to
| nvoHeatPrimary | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV33 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 9 | |
Base type:
| | |
Applies to
| nvoHeatSecondary | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV34 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 10 | |
Base type:
| | |
Applies to
| nvoCoolPrimary | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV35 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 11 | |
Base type:
| | |
Applies to
| nvoOADamper | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV36 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 12 | |
Base type:
| | |
Applies to
| nvoSpaceRH | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV37 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 13 | |
Base type:
| | |
Applies to
| nvoOutdoorRH | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV38 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 14 | |
Base type:
| | |
Applies to
| nvoOutdoorTemp | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV39 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 15 | |
Base type:
| | |
Applies to
| nvoSpaceCO2 | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV40 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 16 | |
Base type:
| | |
Applies to
| nvoEnergyHoldOff | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV01 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 18 | |
Base type:
| | |
Applies to
| nviSpaceTemp | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV03 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 19 | |
Base type:
| | |
Applies to
| nviSetptOffset | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV04 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 20 | |
Base type:
| | |
Applies to
| nviSetptShift | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV05 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 21 | |
Base type:
| | |
Applies to
| nviOccSchedule | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV07 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 22 | |
Base type:
| | |
Applies to
| nviOccSensor | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV08 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 23 | |
Base type:
| | |
Applies to
| nviApplicMode | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV09 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 24 | |
Base type:
| | |
Applies to
| nviHeatCool | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV11 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 25 | |
Base type:
| | |
Applies to
| nviComprEnable | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV12 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 26 | |
Base type:
| | |
Applies to
| nviAuxHeatEnable | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV13 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 27 | |
Base type:
| | |
Applies to
| nviEconEnable | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV14 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 28 | |
Base type:
| | |
Applies to
| nviEnergyHoldOff | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV17 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 29 | |
Base type:
| | |
Applies to
| nviSourceTemp | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV18 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 30 | |
Base type:
| | |
Applies to
| nviOutdoorTemp | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV19 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 31 | |
Base type:
| | |
Applies to
| nviSpaceRH | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBtNV20 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 32 | |
Base type:
| | |
Applies to
| nviOutdoorRH | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciMinOutTm | Minimum send time.: The minimum period of time between consecutive transmissions of the current value.
|
|
| nciLocation | Location: Provides descriptive physical location information related to the object.
|
|
| nciBypassTime | Bypass time.: The maximum amount of time that the controller can be in the bypass (occupancy) mode following the last bypass request. Zero disables the timer.
|
|
| nciManualTime | Manual override time.: The maximum time that the controller will stay in a manual mode following the last request by a network variable input. Zero disables the timer.
|
|
| nciOAMinPos | Minimum range.: The minimum limit of the value of the primary output network variable for the object.
|
|
| nciSpaceCO2Lim | CO2 limit.: CO2 threshold limit, controller to maintain concentration below this limit.
|
|
| nciSpaceHRSetpt | Humidity high limit setpoint.: High limit humidity setpoint for the controlled space. A zero value disables.
|
|
| nciNumValve | Number of output valves.: Used to inform the controller whether it is in a one-valve or two-valve system.
|
|
| nciSndHrtBtNV21 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 43 | |
Base type:
| | |
Applies to
| nvoSpaceTemp | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV22 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 44 | |
Base type:
| | |
Applies to
| nvoEffectSetpt | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciSndHrtBtNV23 | Maximum send time.: The maximum period of time between consecutive transmissions of the current value.
|
| Member Number:
| 45 | |
Base type:
| | |
Applies to
| nvoUnitStatus | | Array:
| not permitted | | Default:
| 0,0 |
|
| nciRcvHrtBt | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
|
| nciRcvHrtBtNV41 | Maximum receive time.:
The maximum period of time that may expire with no updates on the associated input network variables before the object goes into heartbeat failure mode. A zero value disables the mechanism.
|
| Member Number:
| 47 | |
Base type:
| | |
Applies to
| nviSpaceCO2 | | Array:
| not permitted | | Default:
| 0,0 |
|
